Our MDSS7S SmartSensor has been developed to provide a cost effective DALI sensor with a wide range of functions, coupled with a high level of performance.

Housed in a compact moulded enclosure, SmartSensor can operate as part of a managed DALI lighting network, or function as a versatile stand-alone sensor with extensive control capability.

As a stand-alone sensor, the unit is configured using a simple, user-friendly infra-red remote control, with coloured LEDs on the sensor providing feedback for all commands.

As part of a networked system, the sensor settings are managed by a DALI area controller.

The Metway DALI gateway provides an interface between DALI lighting products and our addressable control system. The module acts as a fully functional DALI addressable product with 64 individually programmable addresses. Each address can be a DALI luminaire, emergency inverter, PIR sensor, controlled relay or scene set plate.

The DALI64 is DIN rail mounted and enclosed in a steel powder coated enclosure wired to industry standard terminals.

Twin DALI64 units (i.e with 128 addresses) is also available.

A removeable memory module facilitates fast configuration of a replacement gateway should that be needed. In other words, should an gateway need to be replaced for any reason, no reprogramming is necessary, simply remove the memory module and reinsert it into the new controller.

The Metway "Tee" module is a key component part in the system allowing for pluggable connectivity between components. Utilising the 'G' type range of connectors and is available in two formats, fixed or remote versions, making any component quickly and easily adaptable to the Metway Wiring System.

The 'G' type range of connectors are designed for mains connection according to EN 61 984 ( connecting and disconnecting under load) and used in installations systems when using the latching covers or locking slides ( VDE 0628 ).

The Metway MA-CANPIR passive infra red detector is an addressable sensor for use with the MA addressable range of LCM's and gateways. It detects movement using a PIR sensor, which updates the light controller using a CAN bus interface.

Daylight linking can be configured either to keep lights off when there is sufficient ambient light, or used as part of a closed loop to maintain a pre-set luminance level in a dimmable system.

Connection is made by RJ12 connectors on the back of the unit, there are two of these to allow easy onward connection.

The 4 pole 166G Classic range is Metway's standard connector for non-dimming protocols and is compatible with a range of various switching modules. Combining the Metway switching and tee modules with the following lead assemblies means any non-dimming operating system can quickly and easily be achieved.

The 166G type of connectors are designed for mains connection according to EN 61 984 (connecting and disconnecting under load) and used in installation systems when using the latching covers or locking slides (VDE 0628) Moulding are halogen free, self-extinguishing and low fuming.

Our classic latching lead, can be used in a variety of LCM's (For example: Phillips Dynalite). They are supplied with a 6-pole centre latching plug, to a free end using 1.00mm² LS0H cable. This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding. Alternatively there is an option for black/grey connectors.

The Metway MA-DALIPIR passive infra red detector is an addressable sensor for use with the MA addressable range of LCM's and gateways. It detects movement using a PIR sensor, which updates the light controller using a DALI interface.

Daylight linking can be configured either to keep lights off when there is sufficient ambient light, or used as part of a closed loop to maintain a pre-set luminance level in a dimmable system.

The walk-test mode, indicated by a built-in LED, helps when configuring the detector. The MA-DALIPIR is connected via a screw terminal on the rear in a standard DALI two wire configuration, powered from the data line.

The 4 pole 166G Classic range is Metway's standard connector for non-dimming protocols and is compatible with a range of various switching modules. Combining the Metway switching and tee modules with the following lead assemblies means any non-dimming operating system can quickly and easily be achieved.

The 166G type of connectors are designed for mains connection according to EN 61 984 (connecting and disconnecting under load) and used in installation systems when using the latching covers or locking slides (VDE 0628).

Moulding are halogen free, self-extinguishing and low fuming.

Our classic non-latching box lead, can be used in a variety of LCM's (For example: Delmatic, Ex-Or). They are supplied with a 6-pole centre latching plug, to a free end using 1.00mm² LS0H cable. This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/grey industry standard, connector coding. Alternatively there is an option for black/blue connectors.

The 4 pole 166G Classic range is Metway's standard connector for non-dimming protocols and is compatible with a range of various switching modules. Combining the Metway switching and tee modules with the following lead assemblies means any non-dimming operating system can quickly and easily be achieved.

The 166G type of connectors are designed for mains connection according to EN 61 984 (connecting and disconnecting under load) and used in installation systems when using the latching covers or locking slides (VDE 0628).

Moulding are halogen free, self-extinguishing and low fuming.

Metway can provide leads for other manufacturers lcms, such as Ensto.

The LCM lead is supplied with a 6-pole latching plug, to a free end on 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and length as per your requirements.

These are provided with a blue/white industry standard connector coding.

The 166G (Flat) range of connectors is ideal for applications where space is minimal, due to their low profile. Together with the options of panel mount connectors & moulded tee pieces, these assemblies provide simple connectivity between luminaires.

The 166G(F) range of connectors is designed for main connection according to EN 61 984 (connected and disconnected under load) and used in installation systems when using the additional locking slides (VDE 0628).