The MPROG is a compact infrared handset used for the basic programming of IR enabled Metway products.

Pointing the handset

You must point the handset directly at the device that you want to control or program. When programming a device it is only necessary to point the handset when ‘sending’ a new setting.

Sending settings to a device

To send the programming parameters to the device, it is simply a case of pressing the relevant button for the setting you require. If the setting is in red type, you would press the 'Shift' button (this handset will display a red light to denote this) and then press the setting you require.

The SmartSensor Remote Control (MDSSR) provides a simple, low cost method to configure the SmartSensor range of DALI multisensors. It can also allow a user to remote control lighting managed by SmartSensor.

Compact and easy to use, MDSSR is smaller than a credit card and slips easily into the pocket.

Supplied in a plastic pouch with a Lithium coin battery and Programming Guide.

Our MCC Connection Centre and MDCC standalone addressable LCM, can be connected using the same leads. They are supplied with a 6-pole side latching plug, to a free end using 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding.

Alternatively there is an option for black/grey connectors.

Our Metway fully addressable leads are supplied with a 6-pole side latching plug, to a free end using 1.00mm² LS0H cable. This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding. These leads will connect to the two fully addressable lcm's MA-DD1LCM10/M and also MA-DS10LCM10-S5.

The Metway DALI gateway provides an interface between DALI lighting products and our addressable control system. The module acts as a fully functional DALI addressable product with 64 individually programmable addresses. Each address can be a DALI luminaire, emergency inverter, PIR sensor, controlled relay or scene set plate.

The DALI64 is DIN rail mounted and enclosed in a steel powder coated enclosure wired to industry standard terminals.

Twin DALI64 units (i.e with 128 addresses) is also available.

A removeable memory module facilitates fast configuration of a replacement gateway should that be needed. In other words, should an gateway need to be replaced for any reason, no reprogramming is necessary, simply remove the memory module and reinsert it into the new controller.

Our classic latching lead, can be used in a variety of LCM's (For example: Phillips Dynalite). They are supplied with a 6-pole centre latching plug, to a free end using 1.00mm² LS0H cable. This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding. Alternatively there is an option for black/grey connectors.

Our classic non-latching box lead, can be used in a variety of LCM's (For example: Delmatic, Ex-Or). They are supplied with a 6-pole centre latching plug, to a free end using 1.00mm² LS0H cable. This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/grey industry standard, connector coding. Alternatively there is an option for black/blue connectors.

Metway can provide leads for other manufacturers lcms, such as Ensto.

The LCM lead is supplied with a 6-pole latching plug, to a free end on 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and length as per your requirements.

These are provided with a blue/white industry standard connector coding.

Metway can provide leads for other manufacturers lcms, such as Ex-Or.

The LCM lead is supplied with a 6-pole latching plug, to a free end on 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and length as per your requirements.

These are provided with a black/grey industry standard connector coding.

Metway can provide leads for other manufacturers lcms, such as CP Electronics.

The LCM lead is supplied with a 6-pole latching plug, to a free end on 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and length as per your requirements.

These are provided with a black/blue industry standard connector coding.

Metway can provide leads for other manufacturers lcms, such as Hager Klik.

The LCM lead is supplied with a 6-pole latching plug, to a free end on 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and length as per your requirements.

The PIRSW is a 360° switching PIR sensor. Designed with a low profile for aesthetically demanding architectural projects providing a high quality sensor for simple on / off occupancy control or providing semi-automatic (absence detection) control.

An intelligent photocell is also included to prevent switching of the lights when natural daylight is available Set-up of the sensor is carried out using a remote control handset with program memory allowing one-key commissioning where common settings are used for multiple devices.