The MPROG is a compact infrared handset used for the basic programming of IR enabled Metway products.

Pointing the handset

You must point the handset directly at the device that you want to control or program. When programming a device it is only necessary to point the handset when ‘sending’ a new setting.

Sending settings to a device

To send the programming parameters to the device, it is simply a case of pressing the relevant button for the setting you require. If the setting is in red type, you would press the 'Shift' button (this handset will display a red light to denote this) and then press the setting you require.

The 166G (Flat) range of connectors is ideal for applications where space is minimal, due to their low profile. Together with the options of panel mount connectors & moulded tee pieces, these assemblies provide simple connectivity between luminaires.

The 166G(F) range of connectors is designed for main connection according to EN 61 984 (connected and disconnected under load) and used in installation systems when using the additional locking slides (VDE 0628).

The SmartSensor Remote Control (MDSSR) provides a simple, low cost method to configure the SmartSensor range of DALI multisensors. It can also allow a user to remote control lighting managed by SmartSensor.

Compact and easy to use, MDSSR is smaller than a credit card and slips easily into the pocket.

Supplied in a plastic pouch with a Lithium coin battery and Programming Guide.

The 166G (Flat) range of connectors is ideal for applications where space is minimal, due to their low profile. Together with the options of panel mount connectors & moulded tee pieces, these assemblies provide simple connectivity between luminaires. The 166G(F) range of connectors is designed for main connection according to EN 61 984 (connected and disconnected under load) and used in installation systems when using the additional locking slides (VDE 0628).

The 166G (Flat) range of connectors is ideal for applications where space is minimal, due to their low profile. Together with the options of panel mount connectors & moulded tee pieces, these assemblies provide simple connectivity between luminaires. The 166G(F) range of connectors is designed for main connection according to EN 61 984 (connected and disconnected under load) and used in installation systems when using the additional locking slides (VDE 0628).

Our MCC Connection Centre and MDCC standalone addressable LCM, can be connected using the same leads. They are supplied with a 6-pole side latching plug, to a free end using 1.00mm² LS0H cable.

This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding.

Alternatively there is an option for black/grey connectors.

The 166G (Flat) range of connectors is ideal for applications where space is minimal, due to their low profile. Together with the options of panel mount connectors & moulded tee pieces, these assemblies provide simple connectivity between luminaires. The 166G(F) range of connectors is designed for main connection according to EN 61 984 (connected and disconnected under load) and used in installation systems when using the additional locking slides (VDE 0628).

The 166G (Flat) range of connectors is ideal for applications where space is minimal, due to their low profile. Together with the options of panel mount connectors & moulded tee pieces, these assemblies provide simple connectivity between luminaires. The 166G(F) range of connectors is designed for main connection according to EN 61 984 (connected and disconnected under load) and used in installation systems when using the additional locking slides (VDE 0628).

The 166G (Flat) range of connectors is ideal for applications where space is minimal, due to their low profile. Together with the options of panel mount connectors & moulded tee pieces, these assemblies provide simple connectivity between luminaires. The 166G(F) range of connectors is designed for main connection according to EN 61 984 (connected and disconnected under load) and used in installation systems when using the additional locking slides (VDE 0628).

Our Metway fully addressable leads are supplied with a 6-pole side latching plug, to a free end using 1.00mm² LS0H cable. This can be supplied in a variety of cores, and lengths as per your requirements.

These are supplied with a black/blue industry standard, connector coding. These leads will connect to the two fully addressable lcm's MA-DD1LCM10/M and also MA-DS10LCM10-S5.

The Metway DALI gateway provides an interface between DALI lighting products and our addressable control system. The module acts as a fully functional DALI addressable product with 64 individually programmable addresses. Each address can be a DALI luminaire, emergency inverter, PIR sensor, controlled relay or scene set plate.

The DALI64 is DIN rail mounted and enclosed in a steel powder coated enclosure wired to industry standard terminals.

Twin DALI64 units (i.e with 128 addresses) is also available.

A removeable memory module facilitates fast configuration of a replacement gateway should that be needed. In other words, should an gateway need to be replaced for any reason, no reprogramming is necessary, simply remove the memory module and reinsert it into the new controller.

The Metway "Tee" module is a key component part in the system allowing for pluggable connectivity between components. Utilising the 'G' type range of connectors and is available in two formats, fixed or remote versions, making any component quickly and easily adaptable to the Metway Wiring System.

The 'G' type range of connectors are designed for mains connection according to EN 61 984 ( connecting and disconnecting under load) and used in installations systems when using the latching covers or locking slides ( VDE 0628 ).